Atlas Hydraulics Inc.: OSHA inspections and violations
Brandon, South Dakota · Fluid Power Valve and Hose Fitting Manufacturing · NAICS 332912
1inspections
1citation items
$7,210current penalties
Oct 13, 2020last inspection
OSHA inspectors have visited Atlas Hydraulics Inc. in South Dakota one time.
It opened on Oct 13, 2020 on a referral, in Brandon.
In all, OSHA issued 1 citation item: 1 other-than-serious.
The penalties, $7,210 in total, stand where OSHA first set them.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Atlas Hydraulics Inc. averages $7,210 across 1 cited inspection.
Atlas Hydraulics Inc. also files yearly injury logs with OSHA, summarized below.
It reported 1 severe injury to OSHA since 2015.
Citation items per year, by inspection date.
South Dakota · latest 90 days of OSHA records
29employers cited
Get notified the morning OSHA posts each new citation in South Dakota: the employer, the site address, the rules broken and the penalty.
Incident on Oct 9, 2020: Employee's fingertip is caught in cnc tube bender, is later
At 7:30 a.m. on October 9, 2020, an employee was working for a firm that manufactured fluid power valves and hose fittings. He was a machinist. He was operating a Universal Tool & Engineering (UTE) model M 30 Extended ED CNC tube bender, with serial number 5136. The middle finger on his right hand became caught between the clamp and bend die on the tube bender. As a result, the employee underwent the surgical amputation of his right middle distal phalanx. He was treated without hospitalization. The first shift tube shop supervisor was aware of an earlier employee injury. In December 2019, an employee's fingertip became caught between dies on another CNC tube bender onsite and partially degloved. As a result of that incident, the company installed a Keyence SZ-01S safety laser scanner system on all three CNC tube benders in similar arrangements or positions. Although the company had placed a Keyence SZ-01S safety laser scanner system to monitor the work area around the point of operation of the CNC tube benders, the placement of the safety laser scanner system created unmonitored areas near the point of operation that would not prevent employee access. Additionally, the placement of the safety laser scanner system did not provide an adequate safety distance as prescribed by the manufacturer's operations manual per ISO13855 (2005) and IEC61496-3 (2008) when the operator was working near or with the machine interface or two hand control. Employees did not receive training on the safety laser scanner systems. They were not required to test them routinely. After the incident covered by this inspection, management identified areas near the point of operation that were not monitored by the safety system.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2016, the Brandon site logged 7 recordable injuries or illnesses among about 169 workers: 4.2 per 100 full-time workers, against a median of 2.4 for its industry. Those cases cost 20 days away from work.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Atlas Hydraulics - Brandon
Brandon · 2016
169
7
4
4.2
2.4
Severe injury reports
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 1 report on file.
An employee was operating a tube bender and noticed that one of the pressure dies was misaligned. The employee initiated a manual pause on the bender and then started adjusting the pressure die. A separate pressure die actuated, catching the employee's finger between the pressure die and a tube die causing injury to the distal phalanx of the right middle finger which required medical amputation.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(a) Machine guarding—(1) Types of guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding methods are—barrier guards, two-hand tripping devices, electronic safety devices, etc.
Other fluid power valve and hose fitting manufacturing employers in South Dakota
Alert subscribers get notified of each newly cited employer in South Dakota the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.