Austin Bridge & Road, LP: OSHA inspections and violations
San Antonio, Texas · Highway, Street, and Bridge Construction · NAICS 237310
31inspections
11citation items
$42,806current penalties
Jun 24, 2026last inspection
Since 1991, OSHA inspectors have visited Austin Bridge & Road, LP in Texas 31 times.
The most recent inspection opened on Jun 24, 2026 after a fatality or catastrophe, in Mesquite and is still open.
In all, OSHA issued 11 citation items: 7 serious and 4 other-than-serious.
The proposed penalties came to $44,719; today they stand at $42,806, 4% less.
The rule cited most here is 1926.1052 (stairways in construction), 2 times.
Among construction employers, the typical cited inspection since 2015 ends with a $3,080 penalty. Austin Bridge & Road, LP averages $15,566 across 2 cited inspections.
5 inspections on this page followed a fatal incident.
Austin Bridge & Road, LP also files yearly injury logs with OSHA, summarized below.
It reported 3 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Texas · latest 90 days of OSHA records
399employers cited
12 of them in the same industry
Get notified the morning OSHA posts each new citation in Texas: the employer, the site address, the rules broken and the penalty.
Fatality or catastrophe · Partial · Safety · 150 employees at the site · Open
All Four Lanes Of Interstate 635 S Near Where Hwy 80 Passes Over It. Cranes Stored In Area Near 635 N And S., Mesquite, TX 75149 · Highway, Street, and Bridge Construction · OSHA's record · Phone and website on Google Maps
No citations from this inspection so far.
Inspection 347991291 OPENED JAN 22, 2025Closed
Planned · Partial · Safety · 58 employees at the site · Closed May 12, 2025
Incident on Feb 20, 2005 (fatal): Employee is killed when caught between crane and truck
At approximately 8:30 p.m. on February 20, 2005, Employee #1 was working with fi ve coworkers installing concrete highway traffic barriers. While assisting anoth er employee retrieving bolts from the back of a crane, the crane lurched backwar d. Employee #1 was caught between the crane and the rear of a tractor trailer co ntaining the barriers. He was transported to the Methodist Hospital in Oak Cliff , where he later died of his injuries. A coworker standing next to Employee #1 o n the rear step of the crane sustained bruises and a minor left leg fracture.
No citations from this inspection.
Inspection 305467706 OPENED SEP 9, 2003Closed
Planned · Partial · Safety · 18 employees at the site · Closed Feb 18, 2004
Incident on Jan 16, 2002: Three employees have fractures - crane tips over
On January 16, 2002, a Manitowoc crane was used to lift a concrete beam when the back left side of the crane dipped down into the cribbing causing the boom to g o backwards and hit the concrete barrier. Two employees were using a Terex aeria l lift removing sections of the crane boom. A 175-ton Krupp crane was used to st abilize the crane. The crane was unhooked and hooked to the boom. A Manitex boom truck was also being used to stabilize the Manitowoc crane. The Manitowoc crane uprighted itself, causing the Manitex boom truck to topple over the I-35 overpa ss along with Employee #1. The Manitex boom truck struck the boom of the Terex a erial lift knocking the main basket with the Employees #2 and #3. The Manitowoc crane was being used at its maximum boom angle and rated capacity for the load r adius. The lattice boom was 110 feet. The boom angle was about 82 degrees. The l oad radius was about 21 feet. The concrete beams weighed approximately 74,100 to 75,900 pounds. The rigging and load block weighed about 3,009 pounds. The total weight is approximately 77,109 to 78,909 pounds. The load chart shows for a loa d radius of 21 feet or 21.5 feet to use a boom angle of 80.3 degrees and maximum capacity is 78,860 pounds (the load chart does not have a 21 foot designation b ut has 20 feet for a boom angle of 81.4 degrees and load capacity of 88,230 poun ds). No measurements of the slope were indicated. Interviews indicated that the load after the pick drifted out indicating a slight slope. Also, interviews indi cated that the mats were level north to south, not west to east. Indications are the grade of the slope was more than one percent. All three employees were hosp italized to treat fractures.
Incident on Jul 13, 1998 (fatal): Employee killed when pinned by overturned crane
Employee #1 was working in the vicinity of a crane when it overturned. He became pinned between a flatbed trailer and the crane's superstructure. Employee #1 wa s killed.
No citations from this inspection.
Inspection 300436474 OPENED MAY 5, 1998Closed
Planned · Partial · Safety · 7 employees at the site · Closed May 6, 1998
Incident on Aug 18, 1997 (fatal): Employee crushed and killed when backhoe overturns on slope
Employee #1 was operating a Case 580l backhoe with a bucket full of white rock. He was descending an embankment at an angle when he decided to get off of the ba ckhoe. After Employee #1 dismounted, the vehicle started to tip. The backhoe the n overturned, striking him in the upper back, between the shoulder blades and be low the neck. Employee #1 was killed. The backhoe was equipped with a roll-over protection system.
No citations from this inspection.
Inspection 300512944 OPENED JUN 5, 1997Closed
Referral · Partial · Safety · 75 employees at the site · Closed Jun 30, 1997
Incident on Jul 9, 1993 (fatal): One employee killed, five injured in fuel tank explosion
Employee #1, assisted by Employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching Employee #1 in burning fuel. Employee s #2 and #3 were burned trying to rescue Employee #1, who died. Employees #4, #5 , and #6 were treated for smoke inhalation.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2025, the San Antonio site logged 0 recordable injuries or illnesses among about 57 workers: 0.0 per 100 full-time workers, against a median of 2.2 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
SH 151 Bexar County
San Antonio · 2025
57
0
0
0.0
2.2
AEDP Austin Bergstrom Airport
Austin · 2025
19
0
0
0.0
2.2
US 90 Bexar County
San Antonio · 2024
23
1
0
4.6
2.2
IH 410
San Antonio · 2023
28
2
0
6.8
2.2
310
Dallas · 2023
22
0
0
0.0
2.2
US 82 Fannin County
Bonham · 2021
23
2
1
8.5
2.2
Dallas Love Field Phase III & IV
Dallas · 2020
41
0
0
0.0
2.2
Dallas Love Field Phase 1
Dallas · 2019
26
0
0
0.0
2.2
Included with any plan: 9 more yearly logs from these sites, back to 2017, with each site's average rate over its latest three years. Already a subscriber? Sign in.
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 3 reports on file.
Apr 3, 2024, San Antonio: Hospitalization · fractures · exterior and musculoskeletal structures of the back unspecified
An employee entered into an aerial lift with another worker in order to perform capital form work for an overpass bridge. The employee stepped out of the aerial lift basket and onto the wooden scaffold platform. The worker fell through the platform's walking surface and onto the ground approximately 20 feet below. The employee sustained broken vertebrae and multiple contusions.
Dec 5, 2023, San Antonio: Hospitalization · fractures · nonclassifiable
The injured employee and a co-worker were removing the bolts supporting a section of formwork. As the injured employee went to access the top of the formwork, they fell through the formwork. The employee fell 20 feet to the ground and sustained broken vertebrae and multiple contusions.
An employee was removing asphalt from a buggy auger. The employee's right index finger was amputated in a shear point between the spinning auger and the machine's frame. The auger was not locked out at the time.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(8) Repairs to equipment. Hot work, such as welding or cutting operations, use of spark-producing power tools, and chipping operations shall be permitted only under supervision of an individual in responsible charge. The individual in responsible charge shall make an inspection of the area to be sure that it is safe for the work to be done and that safe procedures will be followed for the work specified.
(7) Training and communication. (i) The employer shall provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees. The training shall include the following:
29 CFR 1910.177 · Servicing multi-piece and single piece rim wheels
29 CFR 1910.177(c)(1)(i)
(i) The employer shall assure that no employee services any rim wheel unless the employee has been trained and instructed in correct procedures of servicing the type of wheel being serviced, and in the safe operating procedures described in paragraphs (f) and (g) of this section.
Alert subscribers get notified of each newly cited employer in Texas the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.