Ball Metalpack, LLC: OSHA inspections and violations
Columbus, Ohio · Metal Can Manufacturing · NAICS 332431
4inspections
7citation items
$32,657current penalties
Oct 13, 2020last inspection
Since 2019, OSHA inspectors have visited Ball Metalpack, LLC in Ohio 4 times.
The most recent inspection opened on Oct 13, 2020 after a complaint, in Columbus.
In all, OSHA issued 7 citation items: 4 serious and 3 other-than-serious.
The proposed penalties came to $55,948; today they stand at $32,657, 42% less.
The rule cited most here is 1910.212 (machine guarding), 3 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Ball Metalpack, LLC averages $8,164 across 4 cited inspections.
Ball Metalpack, LLC also files yearly injury logs with OSHA, summarized below.
It reported 2 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Ohio · latest 90 days of OSHA records
267employers cited
Get notified the morning OSHA posts each new citation in Ohio: the employer, the site address, the rules broken and the penalty.
OSHA records show Ball Metalpack, LLC at 3 sites in 3 states. Together they've had 7 inspections and $40,056 in current penalties.
We match records by employer name and industry, so these sites are likely the same company, not certainly. Franchises and subsidiaries can file under one name.
Included with any plan: the site-by-site record for all 3 sites, with repeat and willful violations and citations per year for the whole company. Already a subscriber? Sign in.
Incident on Jan 27, 2020: Employee amputates finger in pneumatic testing machine
At 2:30 a.m. on January 27, 2020, Employee #1, a Maintainer, was performing a quality test in the assembly department. Every 30 minutes during each 12-hour shift, he removed one metal can from the line and placed it in the "cone tester" machine. The cone tester machine had been manufactured in house and had been in use for approximately 20 years. The machine consisted of a top and bottom cone that put pressure on the can to see if the weld would hold. The bottom cone was a round piece of metal with angled edges where the can was placed. The can was 6 inches in diameter, and the cone was 6 inches at the base. The top cone traveled approximately 2 inches to the top of the can. The machine operated by pneumatic energy at 90 pounds per square inch and was actioned by a lever. Employee #1 placed a can into the cone tester and had his finger on top of the can while he used the lever to lower the top cone. When the cone lowered, his finger was pinched between the top of the can and the top metal cone. He sustained amputation of his right index finger at the first knuckle. He was treated without hospitalization.
Incident on Apr 27, 2019: Employee incurs multiple injuries when crushed by load eleva
At 6:45 p.m. on April 27, 2019, an employee was lowering the load elevator to perform a load change on the Dexter feeder for the MD4 press when one of the four weights became stuck under the magnet. Without locking out the elevator, the employee cleared the weight from the magnet when the elevator fell down the remainder of the travel distance trapping his left leg. The employee was hospitalized with a fracture of the lower left leg, soft tissue injury, and lacerations on back of lower left leg requiring stitches.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2021, the Columbus site logged 7 recordable injuries or illnesses among about 283 workers: 2.2 per 100 full-time workers, against a median of 2.8 for its industry. Those cases cost 16 days away from work.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Ball Metalpack - Columbus, OH
Columbus · 2021
283
7
1
2.2
2.8
Ball Metalpack - Corporate Operations Center -
Columbus · 2021
24
0
0
0.0
2.8
Ball Metalpack - Corporate Operations Center - Columbus, OH
Columbus · 2020
24
0
0
0.0
2.8
Included with any plan: 3 more yearly logs from these sites, back to 2019, with each site's average rate over its latest three years. Already a subscriber? Sign in.
An employee was manually lowering a lift. The elevator weight on the tensioning chain jammed between the frame and elevator; the employee's lower leg was broken as she tried to clear the jam.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(4) Energy control procedure. (i) Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section.
29 CFR 1910.147(c)(6)(ii)
(ii) The employer shall certify that the periodic inspections have been performed. The certification shall identify the machine or equipment on which the energy control procedure was being utilized, the date of the inspection, the employees included in the inspection, and the person performing the inspection.
29 CFR 1910.147(d)
(d) Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence:
Alert subscribers get notified of each newly cited employer in Ohio the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.