Benson Industries Inc: OSHA inspections and violations
Lebanon, Pennsylvania · All Other Miscellaneous General Purpose Machinery Manufacturing · NAICS 333999
1inspections
4citation items
$3,900current penalties
May 19, 2015last inspection
OSHA has inspected Benson Industries Inc once in Pennsylvania.
The inspection began on May 19, 2015 on a referral, in Lebanon.
That inspection ended with 4 citation items: 3 serious and 1 other-than-serious.
Penalties were first proposed at $6,000 and now stand at $3,900, 35% lower after settlements or reviews.
Woodworking machinery comes up most often in these citations: 3 items under 1910.213.
How that compares: the median penalty per cited inspection for manufacturing employers since 2015 is $3,600, and Benson Industries Inc averages $3,900 (1 cited inspection).
Benson Industries Inc also files yearly injury logs with OSHA, summarized below.
It reported 2 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Pennsylvania · latest 90 days of OSHA records
285employers cited
Get notified the morning OSHA posts each new citation in Pennsylvania: the employer, the site address, the rules broken and the penalty.
Incident on May 13, 2015: Employee cuts finger while using a table saw
At 1:45 p.m. on May 13, 2015, an employee was ripping a piece of plywood on a table saw when the plywood kicked back and caused his finger to hit the blade. The employee cut his left index finger with the table saw blade.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2017, the Lebanon site logged 17 recordable injuries or illnesses among about 151 workers: 10.0 per 100 full-time workers, against a median of 2.8 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Benson Industries, Inc.
Lebanon · 2017
151
17
0
10.0
2.8
Severe injury reports
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 2 reports on file.
An employee was acting as a fire watch during operations to weld off steel beams when a steel beam came loose and fell onto his left hand, resulting in partial amputations to four fingers (up to first knuckle) and lacerations to the wrist, face, and ear.
(c) Hand-fed ripsaws. (1) Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely to cause tooth breakage. The hood shall be so mounted as to insure that its operation will be po
29 CFR 1910.213(c)(2)
(2) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced.
29 CFR 1910.213(c)(3)
(3) Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut.
Other all other miscellaneous general purpose machinery manufacturing employers in Pennsylvania
Alert subscribers get notified of each newly cited employer in Pennsylvania the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.