OSHA SearchOSHA records by employer

Camaco Columbus Manufacturing: OSHA inspections and violations

Columbus, Nebraska · Motor Vehicle Seating and Interior Trim Manufacturing · NAICS 336360

4inspections
6citation items
$10,725current penalties
Dec 28, 2015last inspection

Since 2000, OSHA inspectors have visited Camaco Columbus Manufacturing in Nebraska 4 times.

The most recent inspection opened on Dec 28, 2015 on a referral, in Columbus.

In all, OSHA issued 6 citation items: 6 serious.

The proposed penalties came to $17,875; today they stand at $10,725, 40% less.

The rule cited most here is 1910.217 (mechanical power presses), 3 times.

Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Camaco Columbus Manufacturing averages $4,200 across 1 cited inspection.

It reported 1 severe injury to OSHA since 2015.

Camaco Columbus Manufacturing: OSHA citation items per year, 2000 to 2015
Citation items per year, by inspection date.

Nebraska · latest 90 days of OSHA records

29employers cited

Get notified the morning OSHA posts each new citation in Nebraska: the employer, the site address, the rules broken and the penalty.

See who gets cited next

Latest cited in Nebraska

Checking a subcontractor, a client or your own company? Watch Camaco Columbus Manufacturing and get notified the morning OSHA posts a new citation for it.

Watch this company

Inspection history

Inspection 341142313 OPENED DEC 28, 2015Closed

Referral · Partial · Safety · 450 employees at the site · Closed Jul 12, 2016

1851 E 32nd Ave, Columbus, NE 68601 · Automotive Parts and Accessories Stores · OSHA's record · Phone and website on Google Maps

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1910.255(b)(4) · Resistance welding
Serious$7,000$4,200Mar 15, 2016Final

Inspection 306022047 OPENED AUG 10, 2004Closed

Planned · No inspection · Safety · 460 employees at the site · Closed Aug 10, 2004

1851 E 32nd Ave, Columbus, NE 68601 · Motor Vehicle Seating and Interior Trim Manufacturing · OSHA's record · Phone and website on Google Maps

No citations from this inspection.

Inspection 303727606 OPENED MAY 15, 2001Closed

Programmed other · Partial · Safety · 664 employees at the site · Closed Jun 18, 2001

1851 E 32nd Ave, Columbus, NE 68601 · OSHA's record · Phone and website on Google Maps

No citations from this inspection.

Inspection 300059490 OPENED AUG 2, 2000Closed

Complaint · Partial · Safety · 612 employees at the site · Closed Oct 17, 2000

1851 E 32nd Ave, Columbus, NE 68601 · OSHA's record · Phone and website on Google Maps

Incident on Jul 24, 2000: Employee's hand injured when caught in power press

Employee #1 and a coworker were operating a Cleveland part-revolution power pres s. They were running the 110 ton press in the dual operator mode, where there ar e two separate sets of controls. To initiate a cycle, both operators must activa te their two-hand controls simultaneously. Employee #1 and the coworker complete d a cycle and the coworker moved forward to remove a completed part from the lef t side of the die when the brake mechanism of the press failed. He realized the press was coming down and moved his hand away from the danger area. Employee #1 was also reaching into the machine when the die lowered on his right hand with e nough force that he could not remove it from between the upper and lower dies. T he coworker notified a supervisor of the accident and contacted a maintenance pe rson who was in the area. The maintenance person had other employees block the p ress so that the die could not move down any further. The maintenance person the n reversed the power to the press motor so that it would cycle in the opposite d irection. He then actuated the press in the "inch" mode so that he could control its movement. The maintenance worker was able to move the press ram upwards and free Employee #1's hand. He suffered numerous small lacerations and severe brui sing, but doctors predicted a complete recovery within two weeks. Subsequent ins pection of the press revealed that all safety devices were operating correctly. The brake mechanism is actuated pneumatically and springs keep the brake in cont act with the brake plate until air is injected into the brake piston. This cause s the brake/clutch plate to move into contact with the flywheel, cycling the pre ss. In the event the air pressure is too low to move the brake piston, the press will not cycle. The press is designed so that a power or air failure will not c ause it to cycle erratically. In this case, the O-ring which maintains pressure in the brake cylinder had disintegrated and become trapped in the piston sleeve. This caused the brake/clutch plate to jam between the flywheel and the brake pa ds, leaving the machine stuck in a state of limbo. There was no power transfer t o the press so it did not cycle, nor was there any pressure against the brake pa ds to stop the press from rolling over, thus allowing the press to close. This i s not something that can be routinely inspected. To examine the O-ring that fail ed takes a maintenance worker between 10 and 12 hours. The press had been inspec ted by a qualified maintenance worker within 42 hours before the accident, and n o deficiencies were noted.

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1910.212(a)(3)(ii) · Machine guarding
Serious$4,500$2,700Sep 5, 2000Closed
Citation 1, item 2a
29 CFR 1910.217(c)(2)(ia) · Mechanical power presses
Serious$4,500$2,700Sep 5, 2000Closed
Citation 1, item 2b
29 CFR 1910.217(c)(2)(id) · Mechanical power presses
Serious$0$0Sep 5, 2000Closed
Citation 1, item 2c
29 CFR 1910.217(c)(3)(iii) · Mechanical power presses
Serious$0$0Sep 5, 2000Closed
Citation 1, item 3
29 CFR 1910.219(f)(3) · Belts, pulleys and power-transmission parts
Serious$1,875$1,125Sep 5, 2000Closed

Severe injury reports

Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 1 report on file.

Dec 21, 2015, Columbus: Amputation · amputations · finger(s), fingernail(s), n.e.c.

On December 21, 2015 at 1:30am an employee was operating the nut welder and amputated her right index finger.

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.212 · Machine guarding

29 CFR 1910.212(a)(3)(ii)

(ii) The point of operation of machines whose operation exposes an employee to injury, shall be guarded. The guarding device shall be in conformity with any appropriate standards therefor, or, in the absence of applicable specific standards, shall be so designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle.

29 CFR 1910.217 · Mechanical power presses

29 CFR 1910.217(c)(2)(ia)

(2) Point of operation guards. (i) Every point of operation guard shall meet the following design, construction, application, and adjustment requirements:

29 CFR 1910.217(c)(2)(id)

(2) Point of operation guards. (i) Every point of operation guard shall meet the following design, construction, application, and adjustment requirements:

29 CFR 1910.219 · Belts, pulleys and power-transmission parts

29 CFR 1910.255 · Resistance welding

Other motor vehicle seating and interior trim manufacturing employers in Nebraska

Alert subscribers get notified of each newly cited employer in Nebraska the morning it is posted. See the alert plans.

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.