San Mateo, California · Other Millwork (including Flooring) · NAICS 321918
OSHA has inspected Complete Millwork Services, Inc. 4 times in California since 2012.
The latest one began on May 18, 2023 after an accident, in Belmont.
Those inspections ended with 5 citation items: 5 other-than-serious.
Penalties were first proposed at $4,075 and now stand at $2,710, 33% lower after settlements or reviews.
How that compares: the median penalty per cited inspection for manufacturing employers since 2015 is $4,500, and Complete Millwork Services, Inc. averages $483 (3 cited inspections).
Want to know if OSHA cites Complete Millwork Services, Inc. again? Add it to a watchlist and we will email you the morning the citation shows up.
Watch this company401 Island Parkway, Belmont, CA 94002 · Other Millwork (including Flooring) · OSHA's record · Phone and website on Google Maps
| Citation and rule | Type | Proposed | Current | Issued | Status |
|---|---|---|---|---|---|
| Citation 1, item 1 29 CFR 3328(A)(2) |
Other-than-serious | $550 | $550 | Oct 31, 2023 | Final |
450 Concar Drive, San Mateo, CA 94402 · Other Millwork (including Flooring) · OSHA's record · Phone and website on Google Maps
Incident on Oct 19, 2020: Employee partially amputates fingertip on falling panel
At 7:00 a.m. on October 19, 20202, an employee was helping to install an interior wall panel with a coworker. The panel rested on three wooden blocks that were holding it above the floor. In order to hang the panel on hanging cleats, the employee lifted the panel with a pry bar towards his coworker. The panel slipped and dropped, catching the employee's finger against the floor. The employee sustained a partial amputation of the right index fingertip and was treated without hospitalization.
| Citation and rule | Type | Proposed | Current | Issued | Status |
|---|---|---|---|---|---|
| Citation 1, item 1 29 CFR 3395(I) |
Other-than-serious | $150 | $150 | Apr 19, 2021 | Final |
2950 S. Delaware St., San Mateo, CA 94403 · Custom Architectural Woodwork and Millwork Manufacturing · OSHA's record · Phone and website on Google Maps
Incident on Aug 23, 2017: Employee is using a table saw to cut door panel and lacerate
At 8:45 a.m. on August 23, 2017, an employee was cutting a wooden slat for a door panel using a Dewalt DWE 7491 table saw. The employee removed the table saw guard and was making a fine cut when his left hand came into contact with the saw blade and lacerated all of his fingers. The employee was hospitalized.
| Citation and rule | Type | Proposed | Current | Issued | Status |
|---|---|---|---|---|---|
| Citation 1, item 1 29 CFR 1509(A) |
Other-than-serious | $375 | $375 | Dec 14, 2017 | Final |
| Citation 1, item 2 29 CFR 4300(A) |
Other-than-serious | $750 | $375 | Dec 14, 2017 | Final |
Phase 1, Alteration And Renovation Of Gaming Area Entrance Project 12222 New York Ranch Road, Jackson, CA 95642 · Finish Carpentry Contractors · OSHA's record · Phone and website on Google Maps
| Citation and rule | Type | Proposed | Current | Issued | Status |
|---|---|---|---|---|---|
| Citation 1, item 1 29 CFR 1926.404(b)(1)(i) · Ground-fault protection on job sites |
Other-than-serious | $2,250 | $1,260 | Jul 23, 2012 | Final |
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
29 CFR 1926.404(b)(1)(i)
(b) Branch circuits—(1) Ground-fault protection—(i) General. The employer shall use either ground fault circuit interrupters as specified in paragraph (b)(1)(ii) of this section or an assured equipment grounding conductor program as specified in paragraph (b)(1)(iii) of this section to protect employees on construction sites. These requirements are in addition to any other requirements for equipment grounding conductors.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.