OSHA SearchOSHA records by employer

Fusion Frames, LLC: OSHA inspections and violations

New Albany, Mississippi · All Other Miscellaneous Wood Product Manufacturing · NAICS 321999

1inspections
9citation items
$21,216current penalties
May 14, 2019last inspection

Fusion Frames, LLC has one OSHA inspection on record in Mississippi.

OSHA opened it on May 14, 2019 on a referral, in New Albany.

From that inspection OSHA issued 9 citation items: 9 serious.

OSHA proposed $21,216 in penalties and the amount has not been reduced.

Most often, OSHA cited 1910.147, lockout/tagout (5 items).

For context, across all manufacturing employers the median penalty per cited inspection since 2015 is $4,500. Fusion Frames, LLC averages $21,216 over 1 cited inspection in that time.

It reported 2 severe injuries to OSHA since 2015.

Fusion Frames, LLC: OSHA citation items per year, 2019 to 2019
Citation items per year, by inspection date.

Want to know if OSHA cites Fusion Frames, LLC again? Add it to a watchlist and we will email you the morning the citation shows up.

Watch this company

Inspection history

Inspection 344015086 OPENED MAY 14, 2019Closed

Referral · Partial · Safety · 20 employees at the site · Closed Aug 20, 2019

1126 County Road 101, New Albany, MS 38652 · All Other Miscellaneous Wood Product Manufacturing · OSHA's record · Phone and website on Google Maps

Incident on May 7, 2019: Employee partially amputates while operating chop saw

At approximately 1:30 p.m. on May 7, 2019, an employee was cutting wood stock to length with a chop saw. The chop saw blade struck the finger resulting in the amputation of the corner end of the right index finger and was not hospitalized.

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1910.22(a)(1) · Walking-working surfaces
 Serious$3,789$3,789Jun 25, 2019Final
Citation 1, item 2a
29 CFR 1910.147(c)(1) · Lockout/tagout
 Serious$5,304$5,304Jun 25, 2019Final
Citation 1, item 2b
29 CFR 1910.147(c)(4)(i) · Lockout/tagout
 Serious$0$0Jun 25, 2019Final
Citation 1, item 2c
29 CFR 1910.147(c)(5)(i) · Lockout/tagout
 Serious$0$0Jun 25, 2019Final
Citation 1, item 2d
29 CFR 1910.147(c)(6)(i) · Lockout/tagout
 Serious$0$0Jun 25, 2019Final
Citation 1, item 2e
29 CFR 1910.147(c)(7)(i) · Lockout/tagout
 Serious$0$0Jun 25, 2019Final
Citation 1, item 3
29 CFR 1910.213(a)(9) · Woodworking machinery
 Serious$4,546$4,546Jun 25, 2019Final
Citation 1, item 4
29 CFR 1910.213(b)(6) · Woodworking machinery
 Serious$5,304$5,304Jun 25, 2019Final
Citation 1, item 5
29 CFR 1910.305(b)(1)(ii) · Electrical wiring methods
 Serious$2,273$2,273Jun 25, 2019Final

Severe injury reports

Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 2 reports on file.

May 7, 2019, New Albany: Amputation · amputations · fingertip(s)

An employee was operating a chop saw to cut wood and amputated the right index fingertip while indexing a board.

Dec 20, 2017, New Albany: Hospitalization · cuts, lacerations · finger(s), fingernail(s), unspecified

An employee shut down a ripsaw, removed the dust boot, and was reaching under it when the employee's right hand contacted the still moving blade, severely lacerating the thumb and index finger.

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.147 · Lockout/tagout

29 CFR 1910.147(c)(1)

(c) General—(1) Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, start up or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source, and rendered inoperative.

29 CFR 1910.147(c)(4)(i)

(4) Energy control procedure. (i) Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section.

29 CFR 1910.147(c)(5)(i)

(5) Protective materials and hardware. (i) Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware shall be provided by the employer for isolating, securing or blocking of machines or equipment from energy sources.

29 CFR 1910.213 · Woodworking machinery

29 CFR 1910.22 · Walking-working surfaces

29 CFR 1910.305 · Electrical wiring methods

Other all other miscellaneous wood product manufacturing employers in Mississippi

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.