Since 2018, OSHA inspectors have visited Geneva Pipe and Precast in Utah 3 times.
The most recent inspection opened on Feb 23, 2023 as a planned inspection, in Washington.
In all, OSHA issued 6 citation items: 6 serious.
The proposed penalties came to $8,375; today they stand at $4,188, 50% less.
The rule cited most here is 1910.213 (woodworking machinery), 3 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $4,500 penalty. Geneva Pipe and Precast averages $2,094 across 2 cited inspections.
1 inspection on this page followed a fatal incident.
Geneva Pipe and Precast also files yearly injury logs with OSHA, summarized below.
Citation items per year, by inspection date.
Utah · latest 90 days of OSHA records
67employers cited
Get notified the morning OSHA posts each new citation in Utah: the employer, the site address, the rules broken and the penalty.
Incident on Feb 5, 2020 (fatal): Employee falls from aggregate retaining wall and later dies
At 1:00 p.m. on February 5, 2020, Employee #1, employed by a pipe and concrete casting company, was walking along the top of a four foot tall aggregate retaining wall. He slipped and fell ten feet into the concrete aggregate pit. He struck his head on the ground and got a concussion. Employee #1 was hospitalized and later died as a result of the head injury.
No citations from this inspection.
Inspection 342910502 OPENED JAN 30, 2018Closed
Complaint · Partial · Safety · 100 employees at the site · Closed Mar 2, 2018
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2024, the Orem site logged 4 recordable injuries or illnesses among about 105 workers: 2.5 per 100 full-time workers, against a median of 3.4 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Geneva Pipe & Precast - Orem
Orem · 2024
105
4
0
2.5
3.4
Geneva Pipe & Precast - SLC
Salt Lake City · 2023
56
1
0
1.8
3.4
Geneva Pipe & Precast - Washington
Washington · 2023
31
1
0
3.2
3.4
Included with any plan: 10 more yearly logs from these sites, back to 2020, with each site's average rate over its latest three years. Already a subscriber? Sign in.
(6) Guards for moving parts. (i) Exposed moving parts such as gears, set screws, projecting keys, chains, chain sprockets, and reciprocating components which might constitute a hazard under normal operating conditions shall be guarded.
(c) Hand-fed ripsaws. (1) Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely to cause tooth breakage. The hood shall be so mounted as to insure that its operation will be po
29 CFR 1910.213(c)(2)
(2) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced.
29 CFR 1910.219 · Belts, pulleys and power-transmission parts
Alert subscribers get notified of each newly cited employer in Utah the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.