Ifs Coatings Inc.: OSHA inspections and violations
Gainesville, Texas · Paint and Coating Manufacturing · NAICS 325510
4inspections
2citation items
$9,529current penalties
Jun 20, 2023last inspection
Ifs Coatings Inc. has 4 OSHA inspections on record in Texas, the first in 2017.
OSHA's last visit started on Jun 20, 2023 after a fatality or catastrophe, in Gainesville.
Across those inspections OSHA issued 2 citation items: 2 serious.
OSHA proposed $15,881 in penalties. After settlements and reviews the total is $9,529, down 40%.
For context, across all manufacturing employers the median penalty per cited inspection since 2015 is $4,500. Ifs Coatings Inc. averages $4,764 over 2 cited inspections in that time.
1 inspection on this page followed a fatal incident.
Ifs Coatings Inc. also files yearly injury logs with OSHA, summarized below.
It reported 4 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Texas · latest 90 days of OSHA records
401employers cited
Get notified the morning OSHA posts each new citation in Texas: the employer, the site address, the rules broken and the penalty.
Incident on Jun 16, 2023 (fatal): Employee is killed in fall from scissor lift after being sho
At 4:35 p.m. on June 16, 2023, an employee working as a maintenance technician for a paint and coatings manufacturer was replacing a fluorescent light fixture with an LED fixture. The employee was working from a scissor lift. He had not placed the safety chain across the guardrail access on the lift. The 277-Volt circuit that serviced the fixtures had not been deenergized. The fixtures were controlled by a passive infrared motion detector switch integrated into the fixtures. The employee performed the work without adequate illumination since the only light source were two overhead light fixtures. The employee disconnected one fixture and the other turned off during the work since motion was not detected within a time period. A coworker noticed the employee working in the dark and asked the employee if he needed a light. The employee responded yes so the coworker left the area to retrieve a flashlight. After he removed the fixture, the employee placed it across the guardrails of the scissor lift. The employee had partially installed the LED fixture, which was serviced by a metal-clad (MC) cable containing insulated ground, neutral, & hot conductors. The employee connected the neutral and ground leads from the LED lamp to the load side conductors. These circuits became deenergized after the service conductors were disconnected. The LED fixture was hanging from its leads unsupported. The service side neutral conductor was covered by electrical tape while the hot conductor was not. No wire nuts or other splicing connecters were found in the area. While attempting to connect the LED light fixture to power, the employee contacted the energized conductor with his hands. After contact, the employee fell out of the scissor lift approximately 20 feet to the concrete floor below. The employee sustained electrical burns to his hands, and multiple blunt force trauma injuries including skeletal fractures, internal organ injuries, and a traumatic brain injury which killed him.
No citations from this inspection.
Inspection 343622502 OPENED NOV 27, 2018Closed
Referral · Partial · Safety · 150 employees at the site · Closed Jan 28, 2019
Incident on Nov 12, 2018: Employee catches fingers in machine rollers and amputates fi
At 5:15 a.m. on November 12, 2018, an employee caught three fingers in the machine rollers and amputated the tips of each finger. The employee was hospitalized.
Incident on Oct 3, 2017: Employee's finger is amputated in rotary sieve
At 5:40 p.m. on October 3, 2017, Employee #1 began cleaning a rotary sieve. The employee performed lockout/tagout to begin the cleaning process. When the employee realized there was more material in the machine, he exited the ladder, removed LOTO, and started up the machine, causing the machine to push the excess material out. Employee #1 turned off the machine, went back up the ladder to resume the cleaning process, forgetting to perform LOTO. He stuck his hand into the machine and his right index finger was amputated but he was not hospitalized.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2024, the Gainesville site logged 1 recordable injury or illness among about 196 workers: 0.4 per 100 full-time workers, against a median of 2.0 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
IFS Coatings Gainesville
Gainesville · 2024
196
1
0
0.4
2.0
Powder Coating Gainesville
Gainesville · 2021
196
8
3
4.0
2.0
Included with any plan: 2 more yearly logs from these sites, back to 2021, with each site's average rate over its latest three years. Already a subscriber? Sign in.
As employee was clearing a jam in a belt system when their right hand was caught in the part that breaks up the brittle paint into smaller chips and crushed.
Jan 25, 2021, Gainesville: Amputation · amputations · fingertip(s)
An employee was investigating an issue with one of the bag houses. While moving powder away from the flip flop valve (air lock), the air lock opened and the flip flop valve closed and amputated a fingertip.
An employee locked/tagged out a rotary sieve machine and cleaned it. Afterward, the employee removed the lockout/tagout, then noticed there was still material in the machine. The employee started the machine to push the excess material out and was attempting to clean it again when the employee's right hand contacted the rotary sieve, amputating the index finger.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(c) General requirements. (1) The employer shall provide portable fire extinguishers and shall mount, locate and identify them so that they are readily accessible to employees without subjecting the employees to possible injury.
(a) Machine guarding—(1) Types of guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding methods are—barrier guards, two-hand tripping devices, electronic safety devices, etc.
Other paint and coating manufacturing employers in Texas
Alert subscribers get notified of each newly cited employer in Texas the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.