OSHA SearchOSHA records by employer

Jared Gentry: OSHA inspections and violations

Red Boiling Springs, Tennessee · Sawmills · NAICS 321113

1inspections
8citation items
$4,387current penalties
Apr 10, 2019last inspection

Jared Gentry has one OSHA inspection on record in Tennessee.

OSHA opened it on Apr 10, 2019 after a complaint, in Red Boiling Springs.

From that inspection OSHA issued 8 citation items: 8 serious.

OSHA proposed $5,850 in penalties. After settlements and reviews the total is $4,387, down 25%.

Most often, OSHA cited 1910.219, belts, pulleys and power-transmission parts (4 items).

For context, across all manufacturing employers the median penalty per cited inspection since 2015 is $4,500. Jared Gentry averages $4,387 over 1 cited inspection in that time.

Jared Gentry: OSHA citation items per year, 2019 to 2019
Citation items per year, by inspection date.

Want to know if OSHA cites Jared Gentry again? Add it to a watchlist and we will email you the morning the citation shows up.

Watch this company

Inspection history

Inspection 343922076 OPENED APR 10, 2019Closed

Complaint · Partial · Safety · 2 employees at the site · Closed Aug 27, 2019

1979 Rose Hill Rd, Red Boiling Springs, TN 37150 · Sawmills · OSHA's record · Phone and website on Google Maps

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1910.219(c)(4)(i) · Belts, pulleys and power-transmission parts
 Serious$750$562Jun 4, 2019Final
Citation 1, item 2a
29 CFR 1910.219(d)(1) · Belts, pulleys and power-transmission parts
 Serious$1,050$788Jun 4, 2019Final
Citation 1, item 2b
29 CFR 1910.219(e)(1)(i) · Belts, pulleys and power-transmission parts
 Serious$0$0Jun 4, 2019Final
Citation 1, item 3
29 CFR 1910.219(f)(3) · Belts, pulleys and power-transmission parts
 Serious$1,050$788Jun 4, 2019Final
Citation 1, item 4
29 CFR 1910.303(b)(2) · Electrical equipment, general requirements
 Serious$750$562Jun 4, 2019Final
Citation 1, item 5
29 CFR 1910.303(g)(2)(i) · Electrical equipment, general requirements
 Serious$750$562Jun 4, 2019Final
Citation 1, item 6
29 CFR 1910.305(b)(1)(i) · Electrical wiring methods
 Serious$750$562Jun 4, 2019Final
Citation 1, item 7
29 CFR 1910.305(b)(1)(ii) · Electrical wiring methods
 Serious$750$563Jun 4, 2019Final

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.219 · Belts, pulleys and power-transmission parts

29 CFR 1910.219(c)(4)(i)

(4) Projecting shaft ends. (i) Projecting shaft ends shall present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by nonrotating caps or safety sleeves.

29 CFR 1910.219(d)(1)

(d) Pulleys—(1) Guarding. Pulleys, any parts of which are seven (7) feet or less from the floor or working platform, shall be guarded in accordance with the standards specified in paragraphs (m) and (o) of this section. Pulleys serving as balance wheels (e.g., punch presses) on which the point of contact between belt and pulley is more than six feet six inches (6 ft. 6 in.) from the floor or platform may be guarded with a disk covering the spokes.

29 CFR 1910.219(e)(1)(i)

(e) Belt, rope, and chain drives—(1) Horizontal belts and ropes. (i) Where both runs of horizontal belts are seven (7) feet or less from the floor level, the guard shall extend to at least fifteen (15) inches above the belt or to a standard height except that where both runs of a horizontal belt are 42 inches or less from the floor, the belt shall be fully enclosed in accordance with paragraphs (m) and (o) of this section.

29 CFR 1910.303 · Electrical equipment, general requirements

29 CFR 1910.305 · Electrical wiring methods

Other sawmills employers in Tennessee

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.