Inspection 345286256 OPENED APR 27, 2021Closed
Building 02020, Ridgecrest, CA 93555 · National Security · OSHA's record · Phone and website on Google Maps
No citations from this inspection.
Ridgecrest, California · National Security · NAICS 928110
Since 2017, OSHA inspectors have visited Naval Facilities Engineering Command - China Lake Carpenter Shop in California 4 times.
The most recent inspection opened on Apr 27, 2021 as a planned inspection, in Ridgecrest.
In all, OSHA issued 3 citation items: 3 serious.
No penalty came with these citations.
The rule cited most here is 1910.213 (woodworking machinery), 2 times.
Among public administration employers, the typical cited inspection since 2015 ends with a $0 penalty. Naval Facilities Engineering Command - China Lake Carpenter Shop averages $0 across 1 cited inspection.
California · latest 90 days of OSHA records
1,134employers cited
3 of them in the same industry
Get notified the morning OSHA posts each new citation in California: the employer, the site address, the rules broken and the penalty.
See who gets cited nextLatest cited in California
Checking a subcontractor, a client or your own company? Watch Naval Facilities Engineering Command - China Lake Carpenter Shop and get notified the morning OSHA posts a new citation for it.
Watch this companyBuilding 02020, Ridgecrest, CA 93555 · National Security · OSHA's record · Phone and website on Google Maps
No citations from this inspection.
Building 02020, Ridgecrest, CA 93555 · Facilities Support Services · OSHA's record · Phone and website on Google Maps
No citations from this inspection.
Building, Ridgecrest, CA 93555 · National Security · OSHA's record · Phone and website on Google Maps
| Citation and rule | Type | Proposed | Current | Issued | Status |
|---|---|---|---|---|---|
| Citation 1, item 1 29 CFR 1910.28(b)(1)(i) · Fall protection in general industry |
Serious | $0 | $0 | Dec 5, 2017 | Final |
| Citation 1, item 2a 29 CFR 1910.213(c)(2) · Woodworking machinery |
Serious | $0 | $0 | Dec 5, 2017 | Final |
| Citation 1, item 2b 29 CFR 1910.213(c)(3) · Woodworking machinery |
Serious | $0 | $0 | Dec 5, 2017 | Final |
Building, Ridgecrest, CA 93555 · National Security · OSHA's record · Phone and website on Google Maps
No citations from this inspection.
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
29 CFR 1910.213(c)(2)
(2) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced.
29 CFR 1910.213(c)(3)
(3) Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut.
29 CFR 1910.28(b)(1)(i)
(b) Protection from fall hazards—(1) Unprotected sides and edges. (i) Except as provided elsewhere in this section, the employer must ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the following:
Alert subscribers get notified of each newly cited employer in California the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.