Since 2014, OSHA inspectors have visited Richardson Molding, LLC in Mississippi 3 times.
The most recent inspection opened on Nov 6, 2019 on a referral, in Philadelphia.
In all, OSHA issued 10 citation items: 10 serious.
The proposed penalties came to $28,730; today they stand at $19,890, 31% less.
The rule cited most here is 1910.23 (ladders in general industry), 2 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $4,500 penalty. Richardson Molding, LLC averages $6,630 across 1 cited inspection.
Richardson Molding, LLC also files yearly injury logs with OSHA, summarized below.
Citation items per year, by inspection date.
Mississippi · latest 90 days of OSHA records
15employers cited
Get notified the morning OSHA posts each new citation in Mississippi: the employer, the site address, the rules broken and the penalty.
Incident on Oct 30, 2019: Employee's thumb tip is amputated by die during leak test
At 10:45 a.m. on October 30, 2019, an employee was working as a maintenance technician for a firm that manufactured industrial molds. He was working in the facility's engineering lab, programming leak test equipment. During the test, there was a bad leak in some equipment. The correct pressure was not being reached. The guards had been removed from that part of the equipment, as the technician needed to look for the leak. Initially, a soapy water spray was used to identify the source of the leak. The leak was found and repaired immediately. During this process, the firm's service sales manager and the employee were present. After the leak was fixed, a test was done to confirm that there were no other leaks. This test was performed without the guards in place. The maintenance technician replaced a lid for the test and pushed in the lid. His thumb was close to a die that came down as part of the test, and it was pinched. When the employee pulled back his hand in reaction, the tip of his thumb was amputated. He was hospitalized. The sales manager related that the equipment on which the employee was injured was made in-house by the firm and still under development. There were two types of test equipment. One tested the assembly for the battery lid cover, and the other did the air leak test for the lid cover. The employee was injured while using the air leak test equipment. There were no guards in place during the leak test. With the guards in place, the gaps were 0.5 inches (13 mm) on the sides and 0.625 inches (16 mm) on the top. The areas to the side of the air leak test were covered by a transparent guard, similar to a face shield. The sales manager said that, though not expecting the employee to perform another test without the guards, he could have given the employee a tool or something similar to push the lid to the die, thus avoiding the danger zone. Replacing the lid to the die by pushing a cart would have kept the employee at a distance of 21 inches (533 mm).
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2020, the Philadelphia site logged 0 recordable injuries or illnesses among about 17 workers: 0.0 per 100 full-time workers, against a median of 2.6 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Richardson Molding LLC
Philadelphia · 2020
17
0
0
0.0
2.6
Included with any plan: 3 more yearly logs from these sites, back to 2017, with each site's average rate over its latest three years. Already a subscriber? Sign in.
(c) Where the eyes or body of any person may be exposed to injurious corrosive materials, suitable facilities for quick drenching or flushing of the eyes and body shall be provided within the work area for immediate emergency use.
(ii) The point of operation of machines whose operation exposes an employee to injury, shall be guarded. The guarding device shall be in conformity with any appropriate standards therefor, or, in the absence of applicable specific standards, shall be so designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle.
(9) Exposure adjustment. Safety guards of the types described in subparagraphs (3) and (4) of this paragraph, where the operator stands in front of the opening, shall be constructed so that the peripheral protecting member can be adjusted to the constantly decreasing diameter of the wheel. The maximum angular exposure above the horizontal plane of the wheel spindle as specified in paragraphs (b) (3) and (4) of this section shall never be exceeded, and the distance between the wheel periphery and the adjustable tongue or the end of the peripheral member at the top shall never exceed one-fourth inch. (See Figures O-18, O-19, O-20, O-21, O-22, and O-23.)
29 CFR 1910.219 · Belts, pulleys and power-transmission parts
Alert subscribers get notified of each newly cited employer in Mississippi the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.