OSHA SearchOSHA records by employer

Robert George Sheffield: OSHA inspections and violations

Mcminnville, Oregon · All Other Specialty Trade Contractors · NAICS 238990

1inspections
4citation items
$500current penalties
Jan 6, 2020last inspection

OSHA inspectors have visited Robert George Sheffield in Oregon one time.

It opened on Jan 6, 2020 after an accident, in Mcminnville.

In all, OSHA issued 4 citation items: 3 serious and 1 other-than-serious.

The penalties, $500 in total, stand where OSHA first set them.

The rule cited most here is 1910.213 (woodworking machinery), 3 times.

Among construction employers, the typical cited inspection since 2015 ends with a $3,080 penalty. Robert George Sheffield averages $500 across 1 cited inspection.

Robert George Sheffield: OSHA citation items per year, 2020 to 2020
Citation items per year, by inspection date.

Oregon · latest 90 days of OSHA records

388employers cited

Get notified the morning OSHA posts each new citation in Oregon: the employer, the site address, the rules broken and the penalty.

See who gets cited next

Latest cited in Oregon

Checking a subcontractor, a client or your own company? Watch Robert George Sheffield and get notified the morning OSHA posts a new citation for it.

Watch this company

Inspection history

Inspection 344780226 OPENED JAN 6, 2020Closed

Accident · Partial · Safety · 3 employees at the site · Closed Feb 9, 2021

19455 Sw Meadow View Dr, Mcminnville, OR 97128 · All Other Specialty Trade Contractors · OSHA's record · Phone and website on Google Maps

Incident on Dec 17, 2019: Employee amputates fingertip while operating unguarded table

At 1:00 p.m. on December 17, 2019, an employee working as a carpenter apprentice for a construction contractor was using a Delta 10-inch Unisaw Tilting Arbor table saw. The saw did not have an adjustable hood, kickback fingers, dogs or a spreader to protect the employee. The employee was struck by the sawblade amputating her fingertip and was hospitalized.

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1a
29 CFR 1910.213(c)(1) · Woodworking machinery
Serious$500$500Jun 16, 2020Final
Citation 1, item 1b
29 CFR 1910.213(c)(2) · Woodworking machinery
Serious$0$0Jun 16, 2020Final
Citation 1, item 1c
29 CFR 1910.213(c)(3) · Woodworking machinery
Serious$0$0Jun 16, 2020Final
Citation 2, item 2
29 CFR OAR 437-001-0765(13)-1
Other-than-serious$0$0Jun 16, 2020Final

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.213 · Woodworking machinery

29 CFR 1910.213(c)(1)

(c) Hand-fed ripsaws. (1) Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely to cause tooth breakage. The hood shall be so mounted as to insure that its operation will be po

29 CFR 1910.213(c)(2)

(2) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced.

29 CFR 1910.213(c)(3)

(3) Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut.

Other all other specialty trade contractors employers in Oregon

Alert subscribers get notified of each newly cited employer in Oregon the morning it is posted. See the alert plans.

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.