OSHA inspectors have visited Schuco USA LLLP in Connecticut one time.
It opened on Jun 30, 2022 on a referral, in Newington.
In all, OSHA issued 3 citation items: 3 serious.
The proposed penalties came to $10,151; today they stand at $8,200, 19% less.
The rule cited most here is 1910.213 (woodworking machinery), 3 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Schuco USA LLLP averages $8,200 across 1 cited inspection.
Schuco USA LLLP also files yearly injury logs with OSHA, summarized below.
It reported 1 severe injury to OSHA since 2015.
Citation items per year, by inspection date.
Connecticut · latest 90 days of OSHA records
83employers cited
Get notified the morning OSHA posts each new citation in Connecticut: the employer, the site address, the rules broken and the penalty.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2020, the Newington site logged 3 recordable injuries or illnesses among about 90 workers: 3.2 per 100 full-time workers, against a median of 2.3 for its industry. Those cases cost 31 days away from work.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Schuco USA LLLP
Newington · 2020
90
3
2
3.2
2.3
Included with any plan: 1 more yearly log from these sites, back to 2017, with each site's average rate over its latest three years. Already a subscriber? Sign in.
An employee was using a table saw to create blocking for cutting when the wood kicked and the employee suffered a finger amputation and a cut on another finger.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(c) Hand-fed ripsaws. (1) Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut but it shall not offer any considerable resistance to insertion of material to saw or to passage of the material being sawed. The hood shall be made of adequate strength to resist blows and strains incidental to reasonable operation, adjusting, and handling, and shall be so designed as to protect the operator from flying splinters and broken saw teeth. It shall be made of material that is soft enough so that it will be unlikely to cause tooth breakage. The hood shall be so mounted as to insure that its operation will be po
29 CFR 1910.213(c)(2)
(2) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced.
29 CFR 1910.213(c)(3)
(3) Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut.
Other metal window and door manufacturing employers in Connecticut
Alert subscribers get notified of each newly cited employer in Connecticut the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.