OSHA SearchOSHA records by employer

Antonio Lemus: OSHA inspections and violations

Richardson, Texas · Masonry Contractors · NAICS 238140

1inspections
5citation items
$22,698current penalties
May 20, 2025last inspection

Antonio Lemus has one OSHA inspection on record in Texas.

OSHA opened it on May 20, 2025 as a planned inspection, in Richardson, and the case has not closed yet.

From that inspection OSHA issued 5 citation items: 5 serious.

OSHA proposed $22,698 in penalties and the amount has not been reduced.

Most often, OSHA cited 1926.451, scaffolds, general requirements (3 items).

For context, across all construction employers the median penalty per cited inspection since 2015 is $3,078. Antonio Lemus averages $22,698 over 1 cited inspection in that time.

Antonio Lemus: OSHA citation items per year, 2025 to 2025
Citation items per year, by inspection date.

Want to know if OSHA cites Antonio Lemus again? Add it to a watchlist and we will email you the morning the citation shows up.

Watch this company

Inspection history

Inspection 348258708 OPENED MAY 20, 2025Open

Planned · Partial · Safety · 8 employees at the site · Open

1704 E Belt Line Rd, Richardson, TX 75080 · Masonry Contractors · OSHA's record · Phone and website on Google Maps

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1926.451(b)(1)(i) · Scaffolds, general requirements
 Serious$4,256$4,256Sep 25, 2025Final
Citation 1, item 2
29 CFR 1926.451(c)(2) · Scaffolds, general requirements
 Serious$4,256$4,256Sep 25, 2025Final
Citation 1, item 3
29 CFR 1926.451(e)(1) · Scaffolds, general requirements
 Serious$4,256$4,256Sep 25, 2025Final
Citation 1, item 4
29 CFR 1926.453(b)(2)(v) · Aerial lifts
 Serious$4,965$4,965Sep 25, 2025Final
Citation 1, item 5
29 CFR 1926.501(b)(13) · Fall protection in construction
 Serious$4,965$4,965Sep 25, 2025Final

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1926.451 · Scaffolds, general requirements

29 CFR 1926.451(b)(1)(i)

(i) Each platform unit (e.g., scaffold plank, fabricated plank, fabricated deck, or fabricated platform) shall be installed so that the space between adjacent units and the space between the platform and the uprights is no more than 1 inch (2.5 cm) wide, except where the employer can demonstrate that a wider space is necessary (for example, to fit around uprights when side brackets are used to extend the width of the platform).

29 CFR 1926.451(c)(2)

(2) Supported scaffold poles, legs, posts, frames, and uprights shall bear on base plates and mud sills or other adequate firm foundation.

29 CFR 1926.451(e)(1)

(1) When scaffold platforms are more than 2 feet (0.6 m) above or below a point of access, portable ladders, hook-on ladders, attachable ladders, stair towers (scaffold stairways/towers), stairway-type ladders (such as ladder stands), ramps, walkways, integral prefabricated scaffold access, or direct access from another scaffold, structure, personnel hoist, or similar surface shall be used. Crossbraces shall not be used as a means of access.

29 CFR 1926.453 · Aerial lifts

29 CFR 1926.501 · Fall protection in construction

Other masonry contractors employers in Texas

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.