OSHA SearchOSHA records by employer

Integrated Turf Solutions, LLC: OSHA inspections and violations

Chatsworth, Georgia · Carpet and Rug Mills · NAICS 314110

2inspections
7citation items
$214,520current penalties
Apr 25, 2025last inspection

Integrated Turf Solutions, LLC has 2 OSHA inspections on record in Georgia, the first in 2023.

OSHA's last visit started on Apr 25, 2025 to follow up on an earlier case, in Chatsworth.

Across those inspections OSHA issued 7 citation items: 5 serious, 1 willful and 1 other-than-serious.

OSHA proposed $214,520 in penalties and the amount has not been reduced.

Most often, OSHA cited 1910.147, lockout/tagout (3 items).

For context, across all manufacturing employers the median penalty per cited inspection since 2015 is $4,875. Integrated Turf Solutions, LLC averages $214,520 over 1 cited inspection in that time.

1 inspection on this page followed a fatal incident.

Integrated Turf Solutions, LLC: OSHA citation items per year, 2023 to 2025
Citation items per year, by inspection date.

Georgia · latest 90 days of OSHA records

145employers cited

Get notified the morning OSHA posts each new citation in Georgia: the employer, the site address, the rules broken and the penalty.

See who gets cited next

Latest cited in Georgia

Checking a subcontractor, a client or your own company? Watch Integrated Turf Solutions, LLC and get notified the morning OSHA posts a new citation for it.

Watch this company

Inspection history

Inspection 348204850 OPENED APR 25, 2025Closed

Follow-up · Partial · Safety · 75 employees at the site · Closed Sep 30, 2025

799 Industrial Blvd, Chatsworth, GA 30705 · Carpet and Rug Mills · OSHA's record · Phone and website on Google Maps

No citations from this inspection.

Inspection 346694110 OPENED MAY 5, 2023Closed

Fatality or catastrophe · Complete · Safety · 64 employees at the site · Closed Feb 18, 2025

799 Industrial Blvd, Chatsworth, GA 30705 · Carpet and Rug Mills · OSHA's record · Phone and website on Google Maps

Incident on May 4, 2023 (fatal): Operator is killed when crushed in rollup machine

At 3:30 p.m. on May 4, 2023, Employee #1 and coworker were performing non-routine activities such as clearing jams at the Roller Assembly area of the Roll-Up machine. Employee #1 was exposed to crush and caught-in between hazards due to the employer not developing a procedure to control potentially hazardous conditions. The employees would prepare items for shipment as follows: The finished turf material is pulled past the Pull Table and onto the Roll-Up Station. After the turf material has been rolled at the Roll-Up station by a roller assembly, which consisted of two calendars, then it is separated (sliced) at the Cross Cutter section. The operator raises the roller assembly, then the roll (rolled turf material) is released onto the Accumulation Table by sliding off on top of four platforms. These platforms are installed on hydraulic cylinders, which actuate sensors to lower the roller assembly back to its original position and start a new rolling operation. The Accumulation Table is belt driven and stages the rolls from the Roll-Up station to the Wrapper Station. A coworker (Quality Control), who was not assisting Employee #1, was standing near the roller assembly and leaned down on one of the sliding platforms located between the Roll-Up Station and the Accumulation Table. This caused a sensor to actuate the roller assembly to lower, which resulted in crushing the employee's torso. The employee immediately lifted the roller assembly using the control panel; however, the roller assembly went down again on the employee's back. After removal from under the roller assembly, the employee was still responsive. The employee then was taken to a hospital in Tennessee, where he died from his injuries.

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1
29 CFR 1910.36(d)(1) · Exit route design
Serious$6,026$6,026Nov 3, 2023Final
Citation 1, item 2
29 CFR 1910.147(c)(5)(i) · Lockout/tagout
Serious$14,063$14,063Nov 3, 2023Final
Citation 1, item 3 Serious$14,063$14,063Nov 3, 2023Final
Citation 1, item 4
29 CFR 1910.212(a)(3)(ii) · Machine guarding
Serious$14,063$14,063Nov 3, 2023Final
Citation 1, item 5
29 CFR 1910.212(a)(3)(iii) · Machine guarding
Serious$10,046$10,046Nov 3, 2023Final
Citation 2, item 1
29 CFR 1910.147(c)(4)(i) · Lockout/tagout
Willful$156,259$156,259Nov 3, 2023Final
Citation 3, item 1
29 CFR 1910.157(c)(1) · Portable fire extinguishers
Other-than-serious$0$0Nov 3, 2023Final

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.147 · Lockout/tagout

29 CFR 1910.147(c)(4)(i)

(4) Energy control procedure. (i) Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section.

29 CFR 1910.147(c)(5)(i)

(5) Protective materials and hardware. (i) Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware shall be provided by the employer for isolating, securing or blocking of machines or equipment from energy sources.

29 CFR 1910.147(c)(7)(iii)(a)

(A) Retraining shall be provided for all authorized and affected employees whenever there is a change in their job assignments, a change in machines, equipment or processes that present a new hazard, or when there is a change in the energy control procedures.

29 CFR 1910.157 · Portable fire extinguishers

29 CFR 1910.212 · Machine guarding

29 CFR 1910.36 · Exit route design

Other carpet and rug mills employers in Georgia

Alert subscribers get notified of each newly cited employer in Georgia the morning it is posted. See the alert plans.

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.