OSHA SearchOSHA records by employer

Orion Access Control Systems: OSHA inspections and violations

Pantego, Texas · Other Electronic Parts and Equipment Merchant Wholesalers · NAICS 423690

1inspections
3citation items
$3,000current penalties
Dec 16, 2019last inspection

OSHA inspectors have visited Orion Access Control Systems in Texas one time.

It opened on Dec 16, 2019 as a planned inspection, in Pantego.

In all, OSHA issued 3 citation items: 3 serious.

The proposed penalties came to $5,721; today they stand at $3,000, 48% less.

The rule cited most here is 1910.215 (grinders and abrasive wheels), 2 times.

Among wholesale employers, the typical cited inspection since 2015 ends with a $3,425 penalty. Orion Access Control Systems averages $3,000 across 1 cited inspection.

Orion Access Control Systems: OSHA citation items per year, 2019 to 2019
Citation items per year, by inspection date.

Want to know if OSHA cites Orion Access Control Systems again? Add it to a watchlist and we will email you the morning the citation shows up.

Watch this company

Inspection history

Inspection 344514286 OPENED DEC 16, 2019Closed

Planned · Complete · Safety · 13 employees at the site · Closed Dec 31, 2019

2321 W. Arkansas Ln. Suite 900, Pantego, TX 76013 · Other Electronic Parts and Equipment Merchant Wholesalers · OSHA's record · Phone and website on Google Maps

Citation and ruleTypeProposedCurrentIssuedStatus
Citation 1, item 1a
29 CFR 1910.215(a)(4) · Grinders and abrasive wheels
 Serious$1,932$950Dec 17, 2019Final
Citation 1, item 1b
29 CFR 1910.215(b)(9) · Grinders and abrasive wheels
 Serious$0$0Dec 17, 2019Final
Citation 1, item 2
29 CFR 1910.305(g)(2)(ii) · Electrical wiring methods
 Serious$3,789$2,050Dec 17, 2019Final

The rules behind these citations

Current text from the Code of Federal Regulations. Some citations were issued under older wording.

29 CFR 1910.215 · Grinders and abrasive wheels

29 CFR 1910.215(a)(4)

(4) Work rests. On offhand grinding machines, work rests shall be used to support the work. They shall be of rigid construction and designed to be adjustable to compensate for wheel wear. Work rests shall be kept adjusted closely to the wheel with a maximum opening of one-eighth inch to prevent the work from being jammed between the wheel and the rest, which may cause wheel breakage. The work rest shall be securely clamped after each adjustment. The adjustment shall not be made with the wheel in motion.

29 CFR 1910.215(b)(9)

(9) Exposure adjustment. Safety guards of the types described in subparagraphs (3) and (4) of this paragraph, where the operator stands in front of the opening, shall be constructed so that the peripheral protecting member can be adjusted to the constantly decreasing diameter of the wheel. The maximum angular exposure above the horizontal plane of the wheel spindle as specified in paragraphs (b) (3) and (4) of this section shall never be exceeded, and the distance between the wheel periphery and the adjustable tongue or the end of the peripheral member at the top shall never exceed one-fourth inch. (See Figures O-18, O-19, O-20, O-21, O-22, and O-23.)

29 CFR 1910.305 · Electrical wiring methods

29 CFR 1910.305(g)(2)(ii)

(ii) Flexible cords may be used only in continuous lengths without splice or tap. Hard-service cord and junior hard-service cord No. 14 and larger may be repaired if spliced so that the splice retains the insulation, outer sheath properties, and usage characteristics of the cord being spliced.

Other other electronic parts and equipment merchant wholesalers employers in Texas

Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.