Overhead Door Corporation: OSHA inspections and violations
Marion, Ohio · Metal Window and Door Manufacturing · NAICS 332321
13inspections
29citation items
$148,838current penalties
Sep 23, 2026last inspection
Since 1975, OSHA inspectors have visited Overhead Door Corporation in Ohio 13 times.
The most recent inspection opened on Sep 23, 2026 on a referral, in Dalton.
In all, OSHA issued 29 citation items: 9 serious, 2 repeat and 18 other-than-serious.
The proposed penalties came to $232,699; today they stand at $148,838, 36% less.
The rule cited most here is 1910.147 (lockout/tagout), 6 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Overhead Door Corporation averages $24,786 across 6 cited inspections.
Overhead Door Corporation also files yearly injury logs with OSHA, summarized below.
It reported 4 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Ohio · latest 90 days of OSHA records
263employers cited
2 of them in the same industry
Get notified the morning OSHA posts each new citation in Ohio: the employer, the site address, the rules broken and the penalty.
OSHA records show Overhead Door Corporation at 27 sites in 6 states. Together they've had 75 inspections and $231,316 in current penalties.
We match records by employer name and industry, so these sites are likely the same company, not certainly. Franchises and subsidiaries can file under one name.
Included with any plan: the site-by-site record for all 27 sites, with repeat and willful violations and citations per year for the whole company. Already a subscriber? Sign in.
Incident on May 6, 2020: Employee's finger is amputated in metal shear
At 8:00 a.m. on May 6, 2020, an employee was cutting strips of aluminum, approximately 1.5 inches by 4 inches, using the Pexto shear (Serial Number: M-86 66574). The employee was operating the Pexto metal shear to cut strips of aluminum. The employee was standing on the side of the shear with his left hand near the rear of the shear to catch the strips of aluminum as they were cut and with his foot hovering over the control pedal. The employee lost his balance, falling forward, causing his hand to move into the blade area of the shear and his foot to press down on the pedal. The shear blade came down on the employee's left middle finger, amputating it to just behind the nail bed. At the time of the incident there was no guard on the rear end of the Pexto shear to prevent access to the blade as metal was cut. The employee's left middle finger was amputated to the first knuckle. The employee was treated without hospitalization.
Incident on Feb 12, 2019: Employee amputates finger while operating foam compacting ma
At 1:15 p.m. on February 12, 2019, Employee #1 was being trained by a coworker on operating the foam impactor machine. The two employees had loaded the impactor and the coworker proceeded to use the switch to close the platens of foam impactor #2 at a time Employee #1 reached to make an adjustment to a 1.125 spacer. Employee #1's fingers were on top of the spacer moving it, when the coworker operated the switch to close the platens. A platen closed and pinched the ends of three fingers on Employee #1's right hand. Employee #1 was located out of view from the coworker, who was at the machine's operating switch. Employee #1 sustained a crushing injuries to the ends of the right second, third, and fourth fingers that resulted in amputation to the ends of the second and third digits. The employee was hospitalized.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2024, the Conneaut site logged 0 recordable injuries or illnesses among about 48 workers: 0.0 per 100 full-time workers, against a median of 4.6 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Wayne Dalton Plastics
Conneaut · 2024
48
0
0
0.0
4.6
Dalton Plant
Dalton · 2020
105
2
0
1.7
4.6
Wayne Dalton/Overhead Door- Rolling Steel Dalton
Dalton · 2019
117
0
0
0.0
4.6
Todco
Marion · 2019
90
7
2
7.9
3.6
Wayne-Dalton Rolling Door
Dalton · 2017
120
6
0
4.1
3.6
Included with any plan: 6 more yearly logs from these sites, back to 2016, with each site's average rate over its latest three years. Already a subscriber? Sign in.
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 4 reports on file.
Jun 23, 2022, Dalton: Amputation · amputations · fingertip(s)
An employee was putting together two pieces of steel using a sheet metal joining machine. His right thumb slipped and was pinched as he lowered the die set. The thumb tip was amputated.
May 6, 2020, Marion: Amputation · amputations · fingertip(s)
On May 6, 2020, an employee was operating a metal shear to cut 2-inch strips of aluminum. He was attempting to catch the strips behind the shear so they would not fall on the floor. While his hand was behind the machine, the shear was actuated via the foot petal, causing the shear to come down on his left middle finger. His fingertip was amputated to approximately the end of the nail bed.
Jan 31, 2017, Mount Hope: Amputation · amputations · fingertip(s)
An employee was operating the shaper that bevels the edges of small pieces angled to fit into a garage door and contacted the shaper blade amputating a fingertip.
Oct 17, 2015, Mount Hope: Amputation · amputations · finger(s), fingernail(s), n.e.c.
A temporary employee had his left hand middle finger amputated while using a cut-off saw to cut up scrap OSB on or about October 17, 2015.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(4) Energy control procedure. (i) Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section.
29 CFR 1910.147(c)(6)(i)
(6) Periodic inspection. (i) The employer shall conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirements of this standard are being followed.
29 CFR 1910.147(c)(7)(i)
(7) Training and communication. (i) The employer shall provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees. The training shall include the following:
Alert subscribers get notified of each newly cited employer in Ohio the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.