Since 1973, OSHA inspectors have visited Channellock, Inc. in Pennsylvania 18 times.
The most recent inspection opened on Jan 29, 2026 on a referral, in Meadville.
In all, OSHA issued 73 citation items: 44 serious, 1 willful and 28 other-than-serious.
The proposed penalties came to $175,900; today they stand at $111,609, 37% less.
The rule cited most here is 1910.212 (machine guarding), 7 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Channellock, Inc. averages $10,699 across 5 cited inspections.
1 inspection on this page followed a fatal incident.
Channellock, Inc. also files yearly injury logs with OSHA, summarized below.
It reported 2 severe injuries to OSHA since 2015.
The Wage and Hour Division has 1 case on it since 2015, with $159,318 in back wages owed to workers.
Citation items per year, by inspection date.
Pennsylvania · latest 90 days of OSHA records
297employers cited
Get notified the morning OSHA posts each new citation in Pennsylvania: the employer, the site address, the rules broken and the penalty.
Incident on Nov 15, 2021: Employee crushes hand when caught between forklift and pile
At 1:20 a.m. on November 15, 2021, an employee was assisting his coworker with the installation of a sow block for a forging hammer, the coworker was operating a forklift carrying the block. The employee directed his coworker backwards to realign the suspended block. The employee's hand was on top of a pile of timber to which a load strap was attached. As the block was moving, it contacted the bottom of the forging hammer, causing the timber to rotate and the employee's hand was crushed between the timber and the forklift tine. The employee was hospitalized to treat crushing injuries to his hand.
Incident on Oct 31, 2019: Employee partially amputates finger and thumb in press welde
At 4:05 a.m. on October 31, 2019, an employee was packing a set of tools on a press welder. The employee noticed that a wooden spacer block was out of place and attempted to place the block back on the upstroke. The employee's left thumb and ring finger became pinched between the spacer block and the upper stationary frame of the press. The employee partially amputated the left ring finger and thumb and was treated without hospitalization.
Incident on Jun 29, 2000 (fatal): Employee killed by transversing head of cnc machine
Employee #1, a set up worker, was changing a cutter on a CNC (Computer Numerical ly Controlled) machine. He had removed the arbor from the chuck and replaced the cutter, but he then put the arbor in the holder above the operator's station ra ther than back in the chuck. Employee #1 turned the key from 'manual' to 'automa tic' mode and pressed the CYCLE START button on the control panel. The transvers ing head traveled along its programmed path. When the chuck reached the position where it should have been putting the arbor back into the holder, it struck the arbor Employee #1 had already put there and broke its plastic holder, allowing the arbor to fall onto the work table. Employee #1 replaced it, returning it to the chuck, and then cycled the machine again. The arbor would not stay in the ho lder, which was now too loose, and it again fell onto the work table. Employee # 1 shimmed the holder and repeated the process. The holder was still not adjusted properly and, this time, the arbor fell into the bottom of the front of the mac hine. This is where the metal chips were gathered and transported out of the mac hine through an 8 in. by 12 in. opening by means of a small conveyor/bin system. Employee #1 attempted to retrieve the arbor from deep inside the machine by lea ning into the open right side door and using his right hand to pick it up. He wa s leaning against the machine when it started up again. Employee #1 became caugh t and was crushed between the transversing head (right side) and the inside fron t of the machine. It is not known if he hit the CYCLE START button again or if t he machine had been stopped at some point in the program and picked up from wher e it had left off. When his body was discovered, the key was still set in 'autom atic' mode; a coworker had to turn it to 'manual' to back the transversing head off Employee #1. The interlock safety devices on both side doors had two screws removed from their actuator side, rendering them inoperable. If the interlock ha d been working properly and Employee #1 had opened a side door when the machine was set in 'automatic' mode, the transversing head would not have moved inside t he machine.
Citation and rule
Type
Proposed
Current
Issued
Status
Citation 1, item 1
29 CFR 1910.132(a) · Personal protective equipment, general requirements
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2025, the Meadville site logged 8 recordable injuries or illnesses among about 247 workers: 1.7 per 100 full-time workers, against a median of 3.2 for its industry. Those cases cost 186 days away from work.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Channellock, Inc. Plant 1
Meadville · 2025
247
8
7
1.7
3.2
Channellock, Inc. Plant 2
Meadville · 2025
75
4
2
2.5
3.2
Channellock Inc. Plant 1
Meadville · 2024
273
15
2
7.1
3.2
Channellock Inc. Plant 2
Meadville · 2024
99
2
1
2.5
3.2
Channellock Plant 1
Meadville · 2021
273
19
7
8.2
3.2
Channellock Plant 2
Meadville · 2021
99
5
0
5.0
3.2
Included with any plan: 14 more yearly logs from these sites, back to 2016, with each site's average rate over its latest three years. Already a subscriber? Sign in.
An employee was positioning a part inside a restrike hammer (full revolution drop hammer). The employee was wearing his safety pullout devices (metal cable with wristlets) at the time. As the employee positioned the part inside the die, he tripped the machine with his palm. As the ram went to drop, his pullout device (cotton rope connection) broke away from the press and his right hand was…
An employee was helping to install a forging hammer sow block. He was standing near the hammer and guiding a forklift operator who was manipulating the suspended block. The employee was directing the forklift backward to realign the block and had his hand on top of timber that was connected to the load strap. As the block was coming out, it contacted the bottom of the hammer and caused the timber…
Wage and hour cases
Cases by the Labor Department's Wage and Hour Division since 2015: unpaid minimum wage or overtime, child labor, family leave and more.
Period reviewed
Violations
Workers owed
Back wages
Penalties
Feb 18, 2017 to Feb 9, 2019
Meadville
367
367
$159,318
$0
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(2) Within twenty-four (24) hours after the in-patient hospitalization of one or more employees or an employee's amputation or an employee's loss of an eye, as a result of a work-related incident, you must report the in-patient hospitalization, amputation, or loss of an eye to OSHA.
(iv) Handling liquids at point of final use. (a) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be kept in covered containers when not actually in use.
29 CFR 1910.106(e)(2)(ivd)
(iv) Handling liquids at point of final use. (a) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be kept in covered containers when not actually in use.
Alert subscribers get notified of each newly cited employer in Pennsylvania the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.