Spartech LLC has 5 OSHA inspections on record in New Hampshire, the first in 2024.
OSHA's last visit started on Mar 4, 2025 after a complaint, in Ossipee.
Across those inspections OSHA issued 11 citation items: 7 serious and 4 other-than-serious.
OSHA proposed $80,052 in penalties. After settlements and reviews the total is $54,302, down 32%.
Most often, OSHA cited 1910.303, electrical equipment, general requirements (3 items).
For context, across all manufacturing employers the median penalty per cited inspection since 2015 is $4,500. Spartech LLC averages $18,101 over 3 cited inspections in that time.
Spartech LLC also files yearly injury logs with OSHA, summarized below.
It reported 2 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
New Hampshire · latest 90 days of OSHA records
50employers cited
Get notified the morning OSHA posts each new citation in New Hampshire: the employer, the site address, the rules broken and the penalty.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2021, the Ossipee site logged 0 recordable injuries or illnesses among about 30 workers: 0.0 per 100 full-time workers, against a median of 2.6 for its industry.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Spartech LLC - Ossipee
Ossipee · 2021
30
0
0
0.0
2.6
Severe injury reports
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 2 reports on file.
Oct 2, 2024, Ossipee: Amputation · amputations, avulsions, enucleations unspecified · finger or thumb tip(s), nail(s)
An employee was adjusting a powered roller on a printing press when the roller caught their tool and their finger was pulled into the roller, resulting in a fingertip amputation.
May 9, 2024, Ossipee: Amputation · amputations, avulsions, enucleations unspecified · finger or thumb tip(s), nail(s)
An employee was setting up two extruder lines when their left index finger was caught in a nip point and they sustained a partial fingertip amputation.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
(a) Machine guarding—(1) Types of guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding methods are—barrier guards, two-hand tripping devices, electronic safety devices, etc.
(b) Protection from fall hazards—(1) Unprotected sides and edges. (i) Except as provided elsewhere in this section, the employer must ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the following:
29 CFR 1910.303 · Electrical equipment, general requirements
29 CFR 1910.303(b)(6)
(6) Deteriorating agents. Unless identified for use in the operating environment, no conductors or equipment shall be located in damp or wet locations; where exposed to gases, fumes, vapors, liquids, or other agents that have a deteriorating effect on the conductors or equipment; or where exposed to excessive temperatures.
Alert subscribers get notified of each newly cited employer in New Hampshire the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.
