Since 1983, OSHA inspectors have visited Sauder Woodworking Co. in Ohio 21 times.
The most recent inspection opened on Aug 20, 2025 on a referral, in Archbold.
In all, OSHA issued 80 citation items: 41 serious, 2 willful and 37 other-than-serious.
The proposed penalties came to $205,967; today they stand at $91,401, 56% less.
The rule cited most here is 1910.212 (machine guarding), 10 times.
Among manufacturing employers, the typical cited inspection since 2015 ends with a $3,600 penalty. Sauder Woodworking Co. averages $8,476 across 8 cited inspections.
2 inspections on this page followed a fatal incident.
Sauder Woodworking Co. also files yearly injury logs with OSHA, summarized below.
It reported 11 severe injuries to OSHA since 2015.
Citation items per year, by inspection date.
Ohio · latest 90 days of OSHA records
265employers cited
Get notified the morning OSHA posts each new citation in Ohio: the employer, the site address, the rules broken and the penalty.
Incident on Jun 6, 2019: Employee amputates finger while operating edge bander machin
At 8:30 a.m. on June 6, 2019, an employee was working on an edge finishing line when a board became crooked while transitioning onto a bander conveyor. The employee reached in with her left hand to adjust the board and caught her finger between the two pads and the side of the conveyor guard. The employee partially amputated her pinky finger that required medical treatment but was not hospitalized.
Incident on Sep 17, 2018: Employee sustains finger amputation while servicing rotary a
At 10:30 a.m. on September 17, 2018, a maintenance employee was servicing a rotary airlock that was making noise and in need of lubrication. The employee operated an electrical disconnect to shut off the airlock before removing the airlock plug to apply the spray lubricant. He then replaced the plug and restarted the airlock, but the noise was still present. The employee again removed the plug from the airlock to apply additional lubricant but this time while the airlock operated. After removing the plug, the employee saw that there was dust over the plug hole and instinctively used his left index finger to clear the dust prior to spraying the lubricant. While clearing the dust, the employee's finger was caught by the rotating paddle blade, resulting in a partial amputation injury to the end of the finger.
Incident on Apr 6, 2017: Employee amputates hand in running roller press
At approximately 8:15 a.m. on April 6, 2017, Employee #1 was cleaning and removing adhesive residue on the end of a rubber roller. The rubber roller was located on the in feed side of the ME7355 Black Brothers Roller Press. The feed side roller created an ingoing pinch point. Employee #1 was wearing nitrile glove that was caught in the nip point. The roller pulled her right hand into the machine and degloved it. Employee #1 was transported to a medical center, where she received treatment on the hand amputation and was then hospitalized. then hospitalized.
Incident on Aug 11, 2008: Employee is caught between forklifts, crushes pelvis
At approximately 5:30 a.m. on August 11, 2008, Employee #1 was in the ticket rec eiving aisle in the distribution center, facing south. Employee #1 was off of hi s powered industrial truck (PIT) (Crown Model Number 60FCTT-180) filling out loa d-receiving papers on the right rear side of the PIT. A coworker had just receiv ed his order ticket from the receiving station, facing north on the west side of the aisle. The total width of the aisle was approximately 16 feet in the area. The coworker was backing PIT Number 2 (Crown Model Number 60FCTT- 198) from the west to the east side of the aisle (turning radius of 80.9 in.), in order to tra vel south back down the aisle (the width of both PITs was 40 in.). The coworker failed to yield to Employee #1 and his PIT struck Employee #1, creating a caught -between hazard between the two PITs. Employee #1 received crushing injuries to the pelvis area and was life-flighted from the scene. Employee #1 was hospitaliz ed.
Incident on Feb 1, 1991 (fatal): Employee killed when crushed by hopper of floor sweeper
Employee #1 was operating an American Lincoln floor sweeper; he had 8 years expe rience. He needed to empty the unit because he was going over to have the unit c leaned. He was dumping the hopper when he apparently noticed a piece of banding material wrapped around the wheel. He must have entered the hopper area without putting the safety bar in the proper position. The hopper came down, pinching hi m between the hopper and the ground. Employee #1 died.
No citations from this inspection.
Inspection 106279573 OPENED MAY 15, 1990Closed
Accident · Partial · Safety · 500 employees at the site · Closed May 7, 1991
Incident on May 14, 1990 (fatal): Employee killed by unsecured schelling saw
Employee #1 was performing general maintenance on a Schelling saw (#40105) that was not locked out and was not blocked under the beam. He was removing two 1/2 i n. hoses and a junction block that were no longer functional. While Employee #1 was pulling on the hoses to see which one to cut and remove, the hoses tripped t he micro switch. The left beam, which weighed approximately 1,500 lb, came down and struck his head. Employee #1, who was on his side, rolled onto his back and, when found, apparently had a pulse for only a minute or two. He died. There was no lockout policy/procedure. The three limit switches are 24 volt DC. The saw m otor is a 480 volt with manual shut-off.
From the Form 300A summaries employers file with OSHA each year. Rate = recordable cases per 100 full-time workers.
In 2025, the Archbold site logged 18 recordable injuries or illnesses among about 956 workers: 2.2 per 100 full-time workers, against a median of 3.7 for its industry. Those cases cost 18 days away from work.
Site and year
Workers
Cases
Days-away cases
Rate
Industry median
Sauder Woodworking Co
Archbold · 2025
956
18
2
2.2
3.7
Sauder Woodworking Co.
Archbold · 2024
1,203
24
5
2.3
3.7
Included with any plan: 1 more yearly log from these sites, back to 2016, with each site's average rate over its latest three years. Already a subscriber? Sign in.
Employers must report any work-related amputation, in-patient hospitalization or loss of an eye to OSHA within 24 hours. 11 reports on file, the 6 most recent shown.
Aug 12, 2025, Archbold: Amputation · amputations, avulsions, enucleations unspecified · other finger(s) n.e.c.
On August 12, 2025, an employee was scraping material off a stainless steel roller on the wrapper line when their left hand was pulled into the rollers. The employee sustained a finger amputation.
Dec 5, 2022, Archbold: Hospitalization · fractures · thigh(s)
An employee was tagging a load when they tripped over the corner of an outfeed conveyor and fell to the floor, resulting in a femur fracture.
An employee was making an adjustment on a trim saw machine when their right hand contacted the machine, resulting in a partial amputation of their right middle finger with a fracture. The machine was unguarded at the time of the incident after maintenance work was performed on the machine.
Feb 24, 2021, Archbold: Hospitalization · fractures · ankle(s)
On February 24, 2021, an employee was hospitalized with a right ankle fracture after slipping and falling on ice in a parking lot while walking into work.
Nov 26, 2019, Archbold: Amputation · amputations · fingertip(s)
An employee was reaching to operate a lever on a hopper that had been raised by a forklift. The hopper shifted and pinched the employee's left ring finger against the forklift fork. The end of the finger was amputated.
Oct 21, 2019, Archbold: Amputation · amputations · fingertip(s)
On October 21, 2019, at approximately 10:15 p.m., an employee was emptying a hopper into a hog. He used his hand to release the bottom lever when it snapped back and caught his left middle finger, causing a partial fingertip amputation.
The rules behind these citations
Current text from the Code of Federal Regulations. Some citations were issued under older wording.
29 CFR 1904.2 · Partial exemption for establishments in certain industries
(b) Implementation—(1) What do I need to do to complete the OSHA 300 Log? You must enter information about your business at the top of the OSHA 300 Log, enter a one or two line description for each recordable injury or illness, and summarize this information on the OSHA 300-A at the end of the year.
(d) Exposure monitoring—(1) General. (i) Each employer who has a workplace covered by this standard shall monitor employees to determine their exposure to formaldehyde.
(iv) Ventilation. Every inside storage room shall be provided with either a gravity or a mechanical exhaust ventilation system. Such system shall be designed to provide for a complete change of air within the room at least six times per hour. If a mechanical exhaust system is used, it shall be controlled by a switch located outside of the door. The ventilating equipment and any lighting fixtures shall be operated by the same switch. A pilot light shall be installed adjacent to the switch if Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are dispensed within the room. Where gravity ventilation is provided, the fresh air intake, as well as the exhaust outlet from the room, shall be on the exterior of the building in which the room is located.
Alert subscribers get notified of each newly cited employer in Ohio the morning it is posted. See the alert plans.
Source: U.S. Department of Labor, OSHA enforcement data. A citation is OSHA's allegation; employers can contest it, and the status column shows where each item stands. Something wrong on this page? Tell us.